MENU

Latest Print Industry News

Submit Your News
07 November 2018

Pulp Fact, Not Fiction

78
Inkjet-decorated pulp cartons (lid top and sides).
Ink throw distance testing.
IIJ ColourPrint 72 T full colour tower-mode printer for pulp carton. The nose tilts to match the slope of the carton side

The world of packaging is changing. The hedonistic throw away culture of years gone by, where plastic was king, is already a fading memory. The future sees a rejection of the practices that poison our oceans and contaminate our land for generations, instead favouring the recyclable and the sustainable. John Corrall, Managing Director of Industrial Inkjet Limited, discusses how pulp is leading the way in this revolution.

Pulp is made from recycled cellulose, sugar cane or even grass. It has a multitude of potential uses, from internal packaging for electronics to egg boxes, disposable plates to fruit punnets, it can be used for salad boxes or even detergent packs. It can be light but strong and can even be made grease-proof.

The next question is how to decorate these new packages. Nothing looks more drab on a shelf than endless grey or brown packages, so they need to look brightly-coloured and appealing. However, any decoration has to de-ink easily for recycling. For long production runs, flexo is currently used, but for short runs or runs with a lot of variation (for example different types of fruit in the same size punnet) this can mean that more pulp cartons are used for setup than in production (hardly a green solution). Using labels is then the logical alternative, but these can cost more than the pulp carton itself, potentially ruining the commercial viability. So what if an alternative was possible? Print direct to the pulp carton using economic and safe water-based inks in vivid colours? Surely that would be the perfect solution? And in order to achieve this goal, what are the technical challenges to be overcome?

The Right Ink

As with most inkjet projects, the printing hardware has to be right, but the ink is the key. Without the right ink, no project will ever succeed. In the case of pulp packaging, the demands on the ink are widespread:

Bright colours: it’s obvious that bright or strong colours will be needed – but they need to remain bright on what is often a very absorbent material. The water content of the ink may be absorbed quickly, but the pigment needs to stay on or near the pulp surface. Also the carton material itself may be an off-white colour or may be pre-coloured (grass-based pulp packaging is – not surprisingly – green in colour).

Regulatory Requirements: if the carton will be used to hold food then the relevant regulation is EC1935/2004. For the printing ink most customers expect compliance with Swiss Ordinance SR 817.023.21. This regulation defines the materials that may be used in a printing ink for ‘non-direct food contact’. There are tests to check what will migrate out of the ink and into any food contained. We need to worry not just about ink that penetrates through the carton wall from the outside to the inside, but also any cross-contamination between the ink on the outside of a carton and the inside of the carton below it when they are stacked together.

Cost: as ever, the economics will make or break the project. Inkjet ink is always going to be more expensive per-litre than flexo ink but this is compensated for by the lack of setup time (and therefore setup cost) and the lack of waste during setup. The economics will obviously change a lot depending on the extent of the decoration required. For example, the cost of printing a small picture of a strawberry or a plum, plus some text and a barcode, might be only 10% of the cost of decorating the entire top and sides of the carton.

Pulp Media Type: ‘Normal’ water-based inks usually work well on regular pulp cartons. The problem comes with grease-proof cartons that have had the pulp material treated with a hydrophobic coating. The ink simply sits on the surface of the carton and can easily be ‘smudged’ with a finger. With this kind of material, we can use a pre-treatment such as a primer to help fix the ink. Or we can use an alternative ink such as a water-based polymeric ink that will ‘fix’ to the pulp surface when heated. In either case, there is an additional cost to be considered.

Inkjet System

As with any inkjet hardware to be used in-line in a production environment, the system will need to be very reliable. After that there are several aspects to decorating pulp cartons that are a little unusual:

Orientation: high-quality colour inkjet print in an industrial environment usually uses piezo drop-on-demand technology. These inkjet print heads have open nozzle holes and the ink is prevented from falling out by careful application of a small vacuum to the ink supply system. This works fine when printing downwards (for example onto the carton lid) because all of the nozzles in the inkjet print head are at the same height and see the same pressure.

However, when printing cartons such as fruit punnets, we need to print both sides of the punnet at more or less the same time. The inkjet print heads are now in ‘tower’ mode, i.e. the row of nozzles is vertically upwards. The nozzles shoot sideways onto the sides of each punnet as it moves horizontally past. The ink pressure at the top of the print head is always going to be less than the ink pressure at the bottom of the print head. For this to work we need a print head with a wide ‘pressure window’. A combination of the non-wet coating on the inkjet print head, and the shape of the tiny nozzle cone, allows the ink meniscus to survive a significant change in ink pressure along the length of the print head.

Ink Throw Distance: pulp cartons usually have a textured surface and are not highly accurate in their overall dimensions. There may be individual paper fibres sticking up. They also tend to have steps or lips in their design in order to add strength. All of this means that the inkjet print head cannot get close to the carton or there is likely to be a crash. From our experience at IIJ, we are normally asking the inkjet print head to ‘throw’ the ink drops between 3 and 5mm to the carton surface. To an extent this conflicts with the customer’s desire for the highest possible print quality. High quality print needs small ink drops, but small ink drops won’t fly far before they lose momentum and blow away. The best compromise seems to be around 14pL drop size. Quality is still rated as ‘good’ but we can print well onto cartons with curved or stepped surfaces.

Environment

Dust: Pulp carton is dusty. Dust gets onto the inkjet print head nozzle faces and interferes with jetting. This causes missing nozzles in the print and production has to pause while the print heads are cleaned. The most important thing to consider is how to prevent dust reaching the inkjet print heads in the first place. Airflow is very important, so an air-knife may be used to remove dust from the carton well before it approaches the inkjet, and the area around the inkjet might be kept at a positive air pressure. It’s also important that when cleaning of the print heads is eventually required, the process is very quick and minimises down-time.

Heat and humidity: if we are printing the cartons soon after manufacture then we have hot, wet cartons passing close to the inkjet heads. The heat could potentially cause drying of the ink in the nozzles, while the humidity could cause condensation i.e. water droppings forming on the cooler inkjet print heads. As with dust issues, the solution involves airflow. Gently blow away the warm, wet air and the problems are resolved.

Drying

Drying of the printed ink should not be forgotten. Our experience is that on dry cartons a near infra-red (NIR) lamp is an effective solution for drying the ink. However, if the decoration is to be done in-line directly after carton manufacture then the situation is different. In that case, the pulp is still wet – perhaps around 7% water by weight depending on the manufacturing process.

Since the ink is water-based, this doesn’t seem to impact print quality – but it does make drying difficult since in effect the dryer is drying the carton as well as the ink. In this case we have found that hot air can work very well (although it takes up a lot of space).

Demand for pulp carton is about to explode, and the use of inkjet for decoration may well be the ‘next big thing’ for our industry.

John Corrall

John Corrall

Managing Director | http://www.industrialij.com

Industrial Inkjet Ltd
LOCAL DISTRIBUTOR

INDUSTRIAL INKJET LTD

Tel: 0728077231

Email: pieterlegrange@industrialij.com

Website: http://www.industrialij.com

Xerox

LATEST NEWS

Bytes Document Solutions Installs Xerox Iridesse At Ndabase Printing Solutions

08 November 2018 - Bytes Document Solutions (BDS) has installed a Xerox Iridesse production press at Ndabase Printing Solutions. The installation was celebrated at an event held at Ndabase's Pretoria premises on 9 Novem...

Contiweb Discusses The Profitability Of Short Run Jobs In Printing

07 November 2018 - Contiweb marketing manager Erik Andriessen discusses how the rising popularity of short run jobs in the printing industry - be it in the context of gravure, flexo, offset or digital - is an accepte...

Flint Group Demonstrating Labelling And Digital Innovations

07 November 2018 - Flint Group has announced that it will demonstrating its broad range of technologies, systems and solutions that support customer business goals and profitability aims. Among those systems are the ...

Parkside Announces Recoflex-PE Recyclable Flexible Packaging

07 November 2018 - The Parkside Recoflex-PE is a unique fully recyclable single-polymer laminate for crisp, drink and tobacco packaging. The product is suitable for nuts and snacks, most cheeses, coffee, protein powders...

Drupa 2020 Exhibition Topics Reflect Innovative Power Of The Industry

07 November 2018 - In addition to printing and converting processes, the drupa 2020 focus will be on package printing, industrial and functional printing as well as additive manufacturing. The drupa hotspots touchpoi...

GMG Demonstrates Extent Of Its Software Performance

06 November 2018 - GMG was recently presented the opportunity to prove the performance of its software in multicolour solutions at the recent Fogra Multicolor Forum in Munich. The vendor-neutral comparison with t...

BOBST Holds Second Edition Of Vacuum Metallising and Coating Innovations Seminar

06 November 2018 - BOBST recently held its BOBST Vacuum Metallising and Coating Innovations seminar in Jakarta. Participants learnt about the latest innovations and trends in vacuum metallising and atmospheric wet coati...

S-One Expands Into EMEA Region

06 November 2018 - S-One Labels And Packaging (S-OneLP) has announced its expansion into the Europe, Middle East and Africa (EMEA) region. In addition to offering products like the Michelman DigiPrime and DigiGuard in s...

Konica Minolta AccurioPress Production Devices Honoured With Buyers Lab 2019 PRO Awards

06 November 2018 - Konica Minolta South Africa has reported that its AccurioPress 6136 and AccurioPress C3080 digital presses have been recognised by Keypoint Intelligence’s Buyers Lab (BLI) with two 2019 PRO awards, ...
suscribe